Overview:

The RF Receive Against PO with Pick Replenishment is used to receive against PO into Receiving Zones while allowing for direct replenishment of Picking Locations. It is used in conjunction with RF Zone Putaway by allowing Pallets or Carts Locations to be assigned to Receiving Locations and then moved to the Putaway Location for specific Picking Locations arranged into Picking Zones.

As the operator receives product, Coreflex directs the operator to place inventory that is needed to replenish picking locations onto a pallet (the staging location). The pallet has a Coreflex area-shelf-bin location assigned to it (for example PA-A-01) and is assigned a Physical Receiving Location (Physical Area-Shelf-Bin). As product is received, inventory is added to this location in Coreflex.

When Receiving is complete, the pallets (i.e. staging locations) are physically moved to the Picking Replenishment location and the RF Zone Put away function directs the operator to scan a product on the pallet. Next it directs them to the appropriate picking bin needing replenishment.

Setup / Requirements:

Required Features:

• RF

Location and Product Setup:

• This function is designed to receive Base Units of Inventory from a PO onto a Pallet Location assigned to a Receiving Location. Pallet Locations are defined using the Setup Locations Screen by defining the Area Type as Pallet.
• Each Receiving Location is assigned a Receiving Zone using the Setup Locations Screen in the Bin section. Receiving zones are then assigned a Putaway Zone for Replenishment using the Setup Receiving Zones Screen. One Receiving Zone should always be assigned to Over Stock and have a Pallet Assigned to it (Pallet Assignment is part of the High Level Flow below).
• A PO must be in the system and be in a status of Awaiting Receipt.
• The Operator will be prompted to receive the product in increments of its Packsize. The Operator may choose to enter a Partial Quantity to move into the Location.
  • The Product Packsize is defined on the Products Screen.

High Level Flow

• NOTE: As with most RF Function, pressing Enter without entering an Data will always make the Previous Screen appear.
• Inventory is received and placed in a Putaway Staging Location.
• On the RF Terminal, Logon and select Receiving from the Main Menu.
• Select Receive PO (Replen) from the Receiving Menu and the Assign Pallet Screen will appear:

• Enter a 1 to view the current Pallet Assignments to the Receiving Zones. The View Pallet Assignments Screen will appear:

• Enter or 0 to exit the screen and proceed with receiving or enter a Receiving Zone to update the assignment. After entering a Receiving Zone, the Update Receiving Zone Pallet Assignment Screen appears:

• The Receiving Zone Location, current status (Married or Not Married), and instruction line will be displayed. In all cases, the Receiving zone is scanned next. The screen will prompt for a Pallet:

• Scan the Pallet to be married or divorced from the Receiving Zone based on the Instruction Line
• The View Pallet Assignments screen will again be displayed. Repeat the process above until all receiving zones are assigned as desired and enter 0 at the View Pallet Assignment Screen.

• After entering a 0 to exit the View Pallet Assignment Screen, the Enter PO Screen will appear.

• Enter or scan the PO to be received. The Scan Productid screen will appear:

• Enter or Scan either the Product Barcode or the Product ID number. The Scan Pallet Screen will appear::

• The Screen will populate with the Productid, Packsize (shown in parenthesis), Description and the Pallet Location where the product is to be placed. After placing the product in the location, Enter or Scan the Pallet Location Barcode. The Pallet Location must match the one displayed on the screen. The Confirmation Screen will appear:

• Enter a 1 if you wish to move one full carton (of 3 in the example above).
  • The Inventory will be received and the screen will change back to the Scan Product Screen allowing the next product to be scanned.
• Enter a 2 if you wish to specify a quantity to Move.
  • The Enter Partial Qty Screen will appear:

• Enter the desired quantity to be received in base units.
• The Inventory will be received and the screen will change back to the Scan Product Screen allowing the next product to be scanned.
• In all cases the Flow continues at the Scan Productid Screen. Continue to scan until all items are Received. Press enter at the Productid Product and the Close Out PO screen will appear:

• This screen shows the PO Quantity and the Qty received on the PO.
  • Enter a Y/1 to mark the PO as Receiving Complete.
  • Enter a N/0 to leave the PO open so that more items can be received against it.
• The Assign Pallet Screen will appear, press enter to return to the Receiving Menu.